Continuing the chrome delete theme for the Tundra interior, these new Blackout Vent rings will get the job done. They are a complete replacement for the factory Chrome rings(not stick on) and mount from the rear like OEM. Although the installation is a little more involved (dash panel removal is necessary) the fit and finish is as good as factory. SOLD IN A PACK OF 4. ONLY BLACK AND GLOSS AVAILABLE AT THIS TIME

Custom molded door handle covers to eliminate that ugly chrome! These covers are designed to snap on and fit perfectly over 2016-UP Tacoma interior handles. Injection molded from automotive grade ABS and available in different colors to spice up the monochromatic door panel. Or keep it simple with black for a stealth look.

If you have a 4 door truck you should purchase the 4 door kit, it will include 4 handle covers.

If you have a 2 door truck purchase the 2 door kit, it will include 2 handle covers.

 Fits:

2016+ Toyota Tacoma (all models)

INSTALLATION:

NO NEED TO REMOVE THE DOOR PANEL! Simply pull open the handle, slip the front on, and put pressure on the back until it clicks into place.

A Simple but effective solution to hold your gas cap during fill ups. Direct bolt in for an easy installation. Fits OEM Gas caps. Available for Long bed and Short bed.

**INSTALLATION**

1) Remove Phillips head bolt from inside fuel door (TIP: Use a #2 bit on an impact while holding pressure on the door. Toyota has been known to install these tight)

2) Slip Gasshole's right side groove into the metal fuel door

3) Reinstall Screw over Gasshole tab.

A simple and elegant Start button for all Toyota Tacoma models with PUSH TO START. No modifications necessary. The factory push button pops off with the included tool and the new replacement snaps right in it's place. 3D scanned for OEM dimensional accuracy so the fit and finish is just like factory. The Logo is transparent so it will illuminate blue like stock.

Available in 3 different configurations;

RED ENGINE START STOP

RED I/O POWER SYMBOL

BLACK I/O POWER SYMBOL 

*** Does not include start trim ring. (From Chrome Delete Kit or as stand alone product.)

Fits:

2016+ TACOMA must have PUSH TO START BUTTON(smart key)

2020+ Toyota 4Runners must have PUSH TO START BUTTON(smart key)

 Install Guide:

Make your door look clean and factory-finished. This kit will cover screw heads for the door latch, cover the door stop hinge, and cover door locks. Protect your investment with this easy-to-install door maintenance kit for a long-term, sleek finish. Keep your car looking showroom-ready with our Door Clean Up Kit.

2 Door Kit Includes 

• 6 Dots (+2 Extra Replacement Dots) for a total of 8 screw head covers

• 2 Door Stop Hinge Covers

• 2 Door Lock Covers

• 4 Alcohol Wipes

4 Door Kit Includes

• 12 Dots (+3 Extra Replacement Dots) for a total of 15 screw head covers

• 4 Door Stop Hinge Covers

• 4 Door Lock Covers

• 8 Alcohol Wipes

Installation

Installs in just a few minutes. For the dots use supplied alcohol wipes to clean the surface of screw heads, then simply remove adhesive film and stick them on! For the Door Stop Hinge Covers simply snap them on! For the Door Lock Covers,  use supplied alcohol wipes to clean the surface of the door lock, remove the adhesive film, and apply them right on top of the existing door lock!

2005 - 2015 Toyota Tacoma - Includes Style 2 Door Lock Cover

2016-2023 Toyota Tacoma - Includes Style 1 Door Lock Cover

2010 - 2023 Toyota 4Runner - Includes Style 2 Door Lock Cover

2018-2023 Toyota RAV4- Includes Style 1 Door Lock Cover

This is an aftermarket part

Flip key is removed from OEM fob. The key itself can be removed from the knuckle and stored in the case or put on a key ring. The key will not "flip" in our product. 

Includes buttons for the remote start and non-remote start versions. Not compatible with the no-button version.

Standard buttons are hard plastic, soft touch are rubber.

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For 2018+ Wrangler JL and Gladiator JT with key-less entry. Injection molded of high strength and impact resistant PC-ABS plastic. Existing electronics and battery are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 7/64" allen key (included). Made in USA.

Install Notes:

Some users may have difficulty inserting the battery and assembling the case. The instruction video shows proper technique, a small screwdriver can help position the battery as well.

Adjusting the battery contact spring will help the case go together much easier.

Make sure to use a name brand battery with a square side profile such as Duracell. Off brands such as those that may come with the OEM fob with a stepped profile are much more difficult to install.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

Instruction video:

PLEASE WATCH INSTRUCTION VIDEOS BEFORE PURCHASING!

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For 5th Gen 4Runners without push button start, and other Toyota applications. Injection molded of high strength and impact resistant ABS plastic (black is PC-ABS). Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 7/64" allen key (included). Made in USA.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Existing key blade, electronics, battery, transponder chip are reused (not included with purchase) and packaged into the new case, no reprogramming. Re cutting a key is not necessary, however the OEM case must be destroyed to extract the key, as the key is molded into it. In most cases the key will pull out easily, though in some instances it must be cut out. If it is desired to retain the original case/key, an additional OEM shell/key only may be purchased and that key can be cut. Alternatively, the integrated key blade may be discarded altogether and a separate key can be used. This method requires the use of the OEM valet key or purchase of a Toyota key with the G chip (Toyota P/N 89785-08040), this key must be cut and reprogrammed at the dealer or locksmith. In some cases the transponder is easily removed, though in most cases it will be glued and require cutting the case and/or heat for removal, this can be somewhat difficult. If care is not used during removal, the transponder may become damaged and stop working (fob/key will not start vehicle). AJT Design is not responsible from broken transponders.

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

AJT Design is not in any way sponsored by or affiliated with Toyota.

Instruction Video (updated):

Transponder Removal Instructions:

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For 2016-2023 Tacomas, 2020-2021 Tundras, 2020-2021 4Runners with push button start only. Injection molded of high strength and impact resistant PC-ABS plastic. Existing valet key, electronics, battery, buttons, and seal are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 3/32" allen key (included). Made in USA.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

AJT Design is not in any way sponsored by or affiliated with Toyota.

Instruction video:

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For Tacomas and Tundras. Injection molded of high strength and impact resistant ABS plastic. Existing electronics, battery, buttons, and seal are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Robust key ring hole eliminates the common breakage of the factory fob. Assembly requires 7/64" allen key (included). Made in USA.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

AJT Design is not in any way sponsored by or affiliated with Toyota.

Instruction video:

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. Injection molded of high strength and impact resistant ABS plastic. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 7/64" allen key (included). Made in USA.

Applications:

• 2014-2018 Chevrolet Silverado / GMC Sierra
• 2019-2021 Chevrolet Silverado / GMC Sierra (non smart fob)
• 2013-2022 Chevrolet Colorado / GMC Canyon
• 2012-2020 Chevrolet Suburban / Chevrolet Tahoe / GMC Yukon / GMC Yukon XL

Please verify your fob looks like the one in our instruction video/compatible photos. Not compatible with "smart key" models. Compatible with and without the chrome "wings". Compatible with and without remote start (we include 2 different buttons). Compatible with and without remote tailgate/lift glass (multiple buttons included).

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Existing electronics and battery are reused (not included with purchase) and packaged into the new case, no reprogramming.

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

Instruction Video :

Flip key is removed from OEM fob. The key itself can be removed from the knuckle and stored in the case or put on a key ring. The key will not "flip" in our product.

Includes buttons for the remote start and non-remote start versions. Includes both a black and red panic button.  Not compatible with the no-button version.  Included buttons shown below:The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For 2018+ Wrangler JL and Gladiator JT with key-less entry. Injection molded of high strength and impact resistant PC-ABS plastic. Existing electronics and battery are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 7/64" allen key (included). Made in USA.

Install Notes:

Some users may have difficulty inserting the battery and assembling the case. The instruction video shows proper technique, a small screwdriver can help position the battery as well.

Adjusting the battery contact spring will help the case go together much easier.

Make sure to use a name brand battery with a square side profile such as Duracell. Off brands such as those that may come with the OEM fob with a stepped profile are much more difficult to install.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

Instruction video:

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For 2022+ Tundra / 2024+ Tacoma and certain other Toyota applications, please see compatibility photo. Injection molded of high strength and impact resistant PC-ABS plastic. Existing valet key, electronics, battery, and seal are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 3/32" allen key (included). Made in USA.

Button sets include a "Gate", "Gate/AC" and blank button to accommodate other versions, please see compatibility photo. Blank button may be used to block gate or tailgate function, but not "Gate/AC" function.

Both black and red button sets include a red and black panic button.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

AJT Design is not in any way sponsored by or affiliated with Toyota.

Instruction video:

NOTE: Top does not contain "FJ" logo.

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For early year FJ Cruisers. For 1st Gen Tundras and possibly some 1st Gen Tacomas. Injection molded of high strength and impact resistant ABS plastic. Existing electronics, battery, buttons, and seal are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Robust key ring hole eliminates the common breakage of the factory fob. Includes panic button. Assembly requires 7/64" allen key (included). Made in USA.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

AJT Design is not in any way sponsored by or affiliated with Toyota.

Instruction video:

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For certain 2014+ Subaru applications with smart fob only, please see compatibility photo. Injection molded of high strength and impact resistant PC-ABS plastic. Existing valet key, electronics, battery, spring, key button, and seal are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 3/32" allen key (included). Made in USA.

Both black and red button sets include a red and black panic button.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

AJT Design is not in any way sponsored by or affiliated with Subaru.

Instruction Video:

Flip key is removed from OEM fob. The key itself can be removed from the knuckle and stored in the case or put on a key ring. The key will not "flip" in our product.

Includes buttons for the remote start and non-remote start versions. Not compatible with the no-button version.

Standard buttons are hard plastic, soft touch are rubber.

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For 2018+ Wrangler JL and Gladiator JT with key-less entry. Injection molded of high strength and impact resistant ABS plastic. Existing electronics and battery are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 7/64" allen key (included). Made in USA.

Install Notes:

Some users may have difficulty inserting the battery and assembling the case. The instruction video shows proper technique, a small screwdriver can help position the battery as well.

Adjusting the battery contact spring will help the case go together much easier.

Make sure to use a name brand battery with a square side profile such as Duracell. Off brands such as those that may come with the OEM fob with a stepped profile are much more difficult to install.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

Instruction video:

V2 Version Updates:

Valet/emergency key does not package into case like the OEM case or our original 2016+ case. Removing this feature allows for a design that is smaller, stronger and symmetrical.

This is not the same case as the 5th Gen 4Runner Limited version, the outside looks the same but the inside geometry is different.

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For 2016+ Tacomas with push button start only. Injection molded of high strength and impact resistant PC-ABS plastic. Existing electronics, battery, and seal are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 3/32" allen key (included). Made in USA.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

AJT Design is not in any way sponsored by or affiliated with Toyota.

Instruction video:

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For Tacomas and Tundras. Injection molded of high strength and impact resistant ABS plastic. Existing electronics, battery, buttons, and seal are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Robust key ring hole eliminates the common breakage of the factory fob. Assembly requires 7/64" allen key (included). Made in USA.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

AJT Design is not in any way sponsored by or affiliated with Toyota.

Instruction video:

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For certain 2014+ Subaru applications with smart fob only, please see compatibility photo. Injection molded of high strength and impact resistant PC-ABS plastic. Existing valet key, electronics, battery, spring, key button, and seal are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 3/32" allen key (included). Made in USA.

Both black and red button sets include a red and black panic button.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

AJT Design is not in any way sponsored by or affiliated with Subaru.

Instruction Video:

SEE PHOTOS AND SELECT CORRECT BUTTON SET

Slide key is removed from OEM fob. The key itself can be removed from the knuckle and stored in the case or put on a key ring. The key will not "slide" into our product.

Includes buttons for several versions, please review compatible/not compatible photos carefully!

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For 2019+ RAM with key-less entry. Injection molded of high strength and impact resistant PC-ABS plastic. Existing electronics, battery, and seal are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 7/64" allen key (included). Made in USA.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save 4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

Instruction video:

PLEASE WATCH INSTRUCTION VIDEOS BEFORE PURCHASING!

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. Injection molded of high strength and impact resistant ABS plastic. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 3/32" allen key (included). Made in USA.

Applications: (please verify your fob looks like the one in our instruction video/compatible photos)

• 2018-2019 Tundra
• 2016+ Tacoma Manual/SR5/Base (without push button ignition)
• Various Toyota H key

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Existing key blade, electronics, battery, transponder chip are reused (not included with purchase) and packaged into the new case, no reprogramming. Re cutting a key is not necessary, however the OEM case must be destroyed to extract the key, as the key is molded into it. In most cases the key will pull out easily, though in some instances it must be cut out. If it is desired to retain the original case/key, an additional OEM shell/key only may be purchased and that key can be cut. Alternatively, the integrated key blade may be discarded altogether and a separate key can be used. This method requires the use of the OEM valet key or purchase of a Toyota key with the H chip (Toyota P/N 89785-0D170), this key must be cut and reprogrammed at the dealer or locksmith. In some cases the transponder is easily removed, though in most cases it will be glued and require cutting the case and/or heat for removal, this can be somewhat difficult. If care is not used during removal, the transponder may become damaged and stop working (fob/key will not start vehicle). AJT Design is not responsible from broken transponders.

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

AJT Design is not in any way sponsored by or affiliated with Toyota.

Instruction Video :

Transponder Removal Instructions:

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For Jeep Wrangler JKs 2007-2018 and other Chrysler applications using the same factory fob. Compatible with and without factory remote start (2 different buttons are included). Injection molded of high strength and impact resistant ABS plastic. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 7/64" allen key (included). Made in USA.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Existing key blade, electronics, battery, transponder are reused (not included with purchase) and packaged into the new case, no reprogramming. Re cutting a key is not necessary, however the OEM case must be destroyed to extract the key, as the key is molded into it. This requires a simple cutting procedure, see instruction video.

In some rare instances (less than 0.2%), the key in the factory fob may not be compatible with our product. A check for metal in the side circles (see photo) should be made before the key is broken out. AJT DESIGN is not responsible for incompatible keys.

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

Instruction Video:

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For 2022+ Tundra / 2024+ Tacoma and certain other Toyota applications, please see compatibility photo. Injection molded of high strength and impact resistant PC-ABS plastic. Existing valet key, electronics, battery, and seal are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 3/32" allen key (included). Made in USA.

Button sets include a "Gate", "Gate/AC" and blank button to accommodate other versions, please see compatibility photo. Blank button may be used to block gate or tailgate function, but not "Gate/AC" function.

Both black and red button sets include a red and black panic button.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

AJT Design is not in any way sponsored by or affiliated with Toyota.

Instruction video:

Note: Back has AJT logo, not TRD

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For certain 4 button Rav4, Camry and others with push button start only, please see compatibility photo. Injection molded of high strength and impact resistant ABS plastic. Existing valet key, electronics, battery, buttons, and seal are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 3/32" allen key (included). Made in USA.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

AJT Design is not in any way sponsored by or affiliated with Toyota.

Instruction video:

The Injection Fob is a two piece plastic case that replaces the factory case that comes with the vehicle. For 2016-2023 Tacomas, 2020-2021 Tundras, 2020-2021 4Runners with push button start only. Injection molded of high strength and impact resistant PC-ABS plastic. Existing valet key, electronics, battery, buttons, and seal are reused (not included with purchase) and packaged into the new case. Instead of an annular snap fit, this design bolts together with socket head cap screws for a more rugged and straightforward approach. Assembly requires 3/32" allen key (included). Made in USA.

DO NOT USE THREADLOCKER SUCH AS LOCTITE ON THIS PRODUCT!

Order 2 and save $4! Enter coupon code "Qty2" at check out. Contact AJT DESIGN for discounted prices on higher quantities.

AJT Design is not in any way sponsored by or affiliated with Toyota.

Instruction video: